greengate said:I gave a copy of an earlier post regarding this to the service department of my dealer and asked if they were willing to do it for 1 1/2 labor as the previous OP's dealer did it for three hours.
They have been sitting on it because there is some ''rumor" that this may actually come out as a dealer installed option for the earlier cars without it.
Will have to see if anything hatches!
Would you mind sharing the particulars about the hardware with us? What, where and how much?4n7h0ny said:Does anyone have experience doing this mod in a 2013 SV around the Los Angeles area? I am willing to pay for some help with the install, I already purchased all of the hardware. Please email me anthonynava (at) csu.fullerton.edu or you can reply here. Thanks!
fotajoye said:Would you mind sharing the particulars about the hardware with us? What, where and how much?4n7h0ny said:Does anyone have experience doing this mod in a 2013 SV around the Los Angeles area? I am willing to pay for some help with the install, I already purchased all of the hardware. Please email me anthonynava (at) csu.fullerton.edu or you can reply here. Thanks!
4n7h0ny said:fotajoye said:Would you mind sharing the particulars about the hardware with us? What, where and how much?4n7h0ny said:Does anyone have experience doing this mod in a 2013 SV around the Los Angeles area? I am willing to pay for some help with the install, I already purchased all of the hardware. Please email me anthonynava (at) csu.fullerton.edu or you can reply here. Thanks!
Sure, the hardware I purchased is the following from tascaparts.com:
24051-3NF0B
HARNESS BACK DR
$48.56
24052-3NF0C
HARNESS BACK DR
$20.22
28442-3NH0A
REAR CAMERA
$129.69
90606-3NF4B
HANDLE, OUTSIDE
$50.31
01454-N5021
SCREW
$1.34
I am will to pay a reasonable rate for the labor, just name your price.
Ramius83 said:Second, I did successfully a rear view camera using all of the OEM equipment to an 2013 SL model that did not have any rear view camera or all around view. I used the parts list from that one post that someone did with the OEM part numbers. I did NOT need the actual rear hatch harness because that SL already had the 4 camera wires and connector at the hatch where the camera would plug in to. The very first time I put the car into reverse, it worked like a charm.
AZRVExpert said:I just wanted to thank the OP and the other posters that gave out such useful information.
I have a 2011 Leaf with no backup camera but was hoping that this tutorial would work for me too. I can tell you that all the harnesses worked for me and the new handle and camera fit the 2011. My biggest problem was that there was absolutely no wiring from the rear quarter panel to the HU. In fact I should have gone to the plug at the radio first and noticed that there were no wires in pins 56-60 but I didn't and rather than be stuck wasting money and the time I already had into the install, I used the OP's method but with OEM parts.
Rather than buying pins though, I reused three wired pins from the old harness at the rear hatch and put them in the plug at the radio. Everything seems to be working though including the lines that move with steering.
Thanks again.
AZRVExpert said:Did you take any pictures of the harness or wiring during your install?
chuckb said:Ramius83 said:Second, I did successfully a rear view camera using all of the OEM equipment to an 2013 SL model that did not have any rear view camera or all around view. I used the parts list from that one post that someone did with the OEM part numbers. I did NOT need the actual rear hatch harness because that SL already had the 4 camera wires and connector at the hatch where the camera would plug in to. The very first time I put the car into reverse, it worked like a charm.
OK, so my dealer has put in the camera and hatch on my 2013 SL but can't make it work... was this just Plug and Play or did you have to do anything else?
Thanks,
Chuck
MechanicDan said:I just completed an install on my 2013 SV w/CHA. All OEM harnesses and parts except wiring from C-pillar to LF kick panel. OEM Pins in OEM connectors. Only thing non OEM was wires. Works perfect and looks stock.
PM me, I'm in seattle area for install.
scottie said:Has anyone successfully got a third party backup camera to work on a 2013 SV leaf?
I plan to do this tomorrow and am thinking about getting this camera. I don't understand how people are putting a camera under the door handle without drilling a hole for the wires. Getting wires to the license plate looks pretty easy with no drilling required.
Thanks,
Scott
scottie said:Has anyone successfully got a third party backup camera to work on a 2013 SV leaf?
I plan to do this tomorrow and am thinking about getting this camera. I don't understand how people are putting a camera under the door handle without drilling a hole for the wires. Getting wires to the license plate looks pretty easy with no drilling required.
Thanks,
Scott
Enter your email address to join: