garygid
Well-known member
The original SOC-Meter was released with firmware version F1.07 installed.
The version number is displayed as the SOC-Meter powers On.
CAUTION: Do NOT press on the display since it is only lightly glued in place.
----------
Operation:
Tap Red to change Modes (different value groups).
Tap Black to change the value displayed.
If installed according to instructions, the two switches are:
1. The Upper is the Power Switch, Up = always On, middle position = off,
and the down (normal) position is "Use the car's Switched Power", or
On when the car is ON. This is the single-pole switch.
2. The Lower is the CAn-bus Selection Switch, with Up = CAN-CAN,
middle = None, and Down (normal) = EV-CAN bus.
This is the double-pole switch.
----------
NOTE: The Hex File for flashing each Firmware version is on-line at
http://www.wwwsite.com/puzzles/socmeter/" onclick="window.open(this.href);return false;
----------
F1.10: (posted 25 Aug 2013, see the link in my Signature, below)
Adds Mode 4 for setting the LED Brightness (now saved in EEprom).
This allows the code to support the origial and the "replacement"
4-digit, 7-segment LED display from SparkFun.
Adds Mode 5 for display of the four Tire Pressures whenever
the CAR-CAN bus is selected (with the Selector switch UP).
The GIDs are now available from either CAN bus.
----------
F1.09: (Released 12 Oct 2012)
Adds display of "Real SOC" to Mode 1.
Adds Mode 3 to F1.08
Speeds up Power-On boot-up.
Displays Charging amps above 99.9 (as when Quick Charging).
Mode 3: LEAF Logging System (LLS) Mode:
V1: Displays only LLS to give the uP more time to Log.
Mode 2: Battery Pack-Output Mode:
V1: Modified Pack Amps, when Regen or Charging, which normally shows
a negative sign (like -99.9 amps to indicate amps in rather than amps out),
to show 100.0 and up with high charging currents, like those from a QC station.
----------
F1.08: (Released 23 Aug 2011)
Adds Mode 2 to F1.07
Mode 2: Battery Pack-Output Mode:
V1: Displays Pack output Amps (Regen or Charging shows a negative sign),
displaying about 200.0 (output) to -99.9 (input) amps.
V2: Displays Volts (about 350.0 to 400.0 volts).
V3: Power Output as kW, about "C99.9" (Charging-in) to P99.9 (Power-out).
----------
F1.07:
Mode 1: GID Mode:
V1: Displays "GID" value (presumed Fuel Amount) as percent of 281 raw.
V2: Displays the "raw" GID CAN-bus data.
Note: Only has one Mode, the Red button does nothing.
----------
The version number is displayed as the SOC-Meter powers On.
CAUTION: Do NOT press on the display since it is only lightly glued in place.
----------
Operation:
Tap Red to change Modes (different value groups).
Tap Black to change the value displayed.
If installed according to instructions, the two switches are:
1. The Upper is the Power Switch, Up = always On, middle position = off,
and the down (normal) position is "Use the car's Switched Power", or
On when the car is ON. This is the single-pole switch.
2. The Lower is the CAn-bus Selection Switch, with Up = CAN-CAN,
middle = None, and Down (normal) = EV-CAN bus.
This is the double-pole switch.
----------
NOTE: The Hex File for flashing each Firmware version is on-line at
http://www.wwwsite.com/puzzles/socmeter/" onclick="window.open(this.href);return false;
----------
F1.10: (posted 25 Aug 2013, see the link in my Signature, below)
Adds Mode 4 for setting the LED Brightness (now saved in EEprom).
This allows the code to support the origial and the "replacement"
4-digit, 7-segment LED display from SparkFun.
Adds Mode 5 for display of the four Tire Pressures whenever
the CAR-CAN bus is selected (with the Selector switch UP).
The GIDs are now available from either CAN bus.
----------
F1.09: (Released 12 Oct 2012)
Adds display of "Real SOC" to Mode 1.
Adds Mode 3 to F1.08
Speeds up Power-On boot-up.
Displays Charging amps above 99.9 (as when Quick Charging).
Mode 3: LEAF Logging System (LLS) Mode:
V1: Displays only LLS to give the uP more time to Log.
Mode 2: Battery Pack-Output Mode:
V1: Modified Pack Amps, when Regen or Charging, which normally shows
a negative sign (like -99.9 amps to indicate amps in rather than amps out),
to show 100.0 and up with high charging currents, like those from a QC station.
----------
F1.08: (Released 23 Aug 2011)
Adds Mode 2 to F1.07
Mode 2: Battery Pack-Output Mode:
V1: Displays Pack output Amps (Regen or Charging shows a negative sign),
displaying about 200.0 (output) to -99.9 (input) amps.
V2: Displays Volts (about 350.0 to 400.0 volts).
V3: Power Output as kW, about "C99.9" (Charging-in) to P99.9 (Power-out).
----------
F1.07:
Mode 1: GID Mode:
V1: Displays "GID" value (presumed Fuel Amount) as percent of 281 raw.
V2: Displays the "raw" GID CAN-bus data.
Note: Only has one Mode, the Red button does nothing.
----------